青青久久av北条麻妃黑人,国产伦理精品,国产精品爽爽爽爽爽爽在线观看,精品国产乱码久久久久久虫虫漫画

PA66 AKV 30 GIT H2.0 900116德國朗盛Durethan 30%玻纖熱老化穩(wěn)定尼龍66塑料（18024445500）

PA 66, 30 % glass fibers, injection molding, heat-aging stabilized, improved surface finish, GIT/WIT



ISO Shortname: ISO 1874-PA 66, GHR, 14-090, GF30

Property Test Condition Unit Standard guide value
d.a.m. cond.
Rheological properties
Molding shrinkage, parallel 150x105x3; 290 °C / MT 80 °C; 500 bar % acc. ISO 2577 0.22　
Molding shrinkage, transverse 150x105x3; 290 °C / MT 80 °C; 500 bar % acc. ISO 2577 0.93　
Post- shrinkage, parallel 150x105x3; 120 °C; 4 h % acc. ISO 2577 0.04　
Post- shrinkage, transverse 150x105x3; 120 °C; 4 h % acc. ISO 2577 0.08　

Mechanical properties (23 °C/50 % r. h.)
C Tensile modulus 1 mm/min MPa ISO 527-1,-2 9200 6600
C Tensile Stress at break 5 mm/min MPa ISO 527-1,-2 190 120
C Tensile Strain at break 5 mm/min % ISO 527-1,-2 4.0 6.0
C Charpy impact strength 23 °C kJ/m² ISO 179-1eU 70 80
C Charpy impact strength -30 °C kJ/m² ISO 179-1eU 60 60
C Charpy notched impact strength 23 °C kJ/m² ISO 179-1eA 10 15
C Charpy notched impact strength -30 °C kJ/m² ISO 179-1eA < 10 < 10
Charpy notched impact strength -40 °C kJ/m² ISO 179-1eA < 10 < 10
Izod impact strength 23 °C kJ/m² ISO 180-1U 60 70
Izod impact strength -30 °C kJ/m² ISO 180-1U 50 50
Izod notched impact strength 23 °C kJ/m² ISO 180-1A 10 15
Izod notched impact strength -30 °C kJ/m² ISO 180-1A 10 10
Flexural modulus 2 mm/min MPa ISO 178-A 8500 6000
Flexural strength 2 mm/min MPa ISO 178-A 280 180
Flexural strain at flexural strength 2 mm/min % ISO 178-A 4.5 6.0
Flexural stress at 3.5 % strain 2 mm/min MPa ISO 178-A 260 160
C Puncture maximum force 23 °C N ISO 6603-2 850 1040
C Puncture maximum force -30 °C N ISO 6603-2 770　
C Puncture energy 23 °C J ISO 6603-2 2.5 4.0
C Puncture energy -30 °C J ISO 6603-2 2.3　
Ball indentation hardness　N/mm² ISO 2039-1 215　

Thermal properties
C Melting temperature 10 °C/min °C ISO 11357-1,-3 260　
C Temperature of deflection under load 1.80 MPa °C ISO 75-1,-2 230　
C Temperature of deflection under load 0.45 MPa °C ISO 75-1,-2 250　
C Temperature of deflection under load 8.00 MPa °C ISO 75-1,-2 90　
Vicat softening temperature 50 N; 120 °C/h °C ISO 306 >230　
C Coefficient of linear thermal expansion, parallel 23 to 55 °C 10-4/K ISO 11359-1,-2 0.3　
C Coefficient of linear thermal expansion, transverse 23 to 55 °C 10-4/K ISO 11359-1,-2 0.8　
C Burning behavior UL 94 (1.6 mm)　Class UL 94 HB　
Burning behavior UL 94　Class UL 94 HB　
C Oxygen index Method A % ISO 4589-2 25　
Glow wire test (GWFI) 2.0 mm °C IEC 60695-2-12 650　
Burning behavior US-FMVSS302 >=1.0 mm　ISO 3795 passed　
C Vicat softening temperature 50 N; 50 °C/h °C ISO 306 > 230　

Electrical properties (23 °C/50 % r. h.)
C Relative permittivity 100 Hz - IEC 60250 4.0 8.0
C Relative permittivity 1 MHz - IEC 60250 3.8 4.2
C Dissipation factor 100 Hz 10-4 IEC 60250 80 2100
C Dissipation factor 1 MHz 10-4 IEC 60250 160 700
C Volume resistivity　Ohm·m IEC 60093 1E13 1E10
C Surface resistivity　Ohm IEC 60093 1E15 1E13
C Electric strength 1 mm kV/mm IEC 60243-1 45 40
C Comparative tracking index CTI Solution A V IEC 60112 475　

Other properties (23 °C)
C Water absorption (Saturation value) Water at 23 °C % ISO 62 6.0　
C Water absorption (Equilibrium value) 23 °C; 50 % RH % ISO 62 2.0　
C Density　kg/m³ ISO 1183 1368　
Bulk density　kg/m³ ISO 60 700　

Processing conditions for test specimens
C Injection molding-Melt temperature　°C ISO 294 290　
C Injection molding-Mold temperature　°C ISO 294 80　

Processing recommendations
Drying temperature dry air dryer　°C - 80　
Drying time dry air dryer　h - 2-6　
Residual moisture content　% Acc. to Karl Fischer　0.03-0.12　
Melt temperature (Tmin - Tmax)　°C - 280-300　
Mold temperature　°C - 80-120　

C These property characteristics are taken from the CAMPUS plastics data bank and are based on the international catalogue of basic data for plastics according to ISO 10350.