無錫禮堂會議廳地坪價格是多少 400-0709-910(請撥打400-0709-910電話，永堅地坪公司)
做一個質量穩定的金剛砂耐磨地坪是每一個甲方甚至乙方客戶所追求的，然而在金剛砂耐磨地坪施工完成后容易出現各類各樣的質量問題，下面我們就以金剛砂耐磨地坪常見的龜裂現象分析一下，金剛砂耐磨地坪成型后出現龜裂的原因主要有以下幾個方面：
1、收光不到位，致密性不好；
2、掌握好混凝土初凝期，提漿時不能灑水；
3、必須要用養護劑（原液一桶做500平方，夏季收光完成3個小時后可進行養護，用拖布即可。養護劑冬季凍住后仍可使用）；
4、混凝土（水灰比）標號不夠；
5、混凝土凝固時間過長；
6、材料用量的多少或 多彩藝術地坪硬化劑是一種即使可用的含特殊礦物骨料、無機顏料及添加劑的高強度耐磨地坪材料，其優點是易施工、一次成型、使用期長、施工快捷、修復方便、著色均勻、不易褪色等優點。同時又解決了普通彩色道板磚的整體性差、高低不平、易松動、使用周期短等缺點。 用本硬化劑材料制作的彩色壓花地坪耐磨、防滑、抗凍、不起塵、易清潔、高密度、高強度、耐沖擊、高雅大方且圖案顏色立體層次強，可隨意選擇搭配。是目前廣場、停車場、街道、公園小道、生活小區、市政道路采用的理想**地坪，是取代彩色道板磚的理想替代產品。藝術壓花地坪
多彩藝術地坪施工方案：
一、基層混凝土的施工要求： 基層砼的強度 C25，其水灰比盡可能小
二、施工工序：
1． 檢查混凝土基礎層質量：完全符合技術要求情況開始施工。
2．砼表面拉毛處理：在新澆注的混凝土表面上加上C25水泥砂漿1cm厚度。
3．選擇模具： 按客戶之要求選擇顏色料及圖案模具。
4．撒布硬化材料：將規定的用量的2/3硬化劑均勻的的撒布在初凝階段的混凝土表面，一般劑量為4公斤/平方米。待硬化劑吸水潤濕后用手工鐵板找平壓光，等地坪再凝一定階段，再進行第二次1/3材料撒布找平壓光作業。
5．找平收光：檢查磨光表面質量，檢查有無裂紋，氣泡、夾渣、色均度，根據混凝土的收光找平作業，收光操作相互交錯進行。
6．撒布脫模粉：在硬化材料處凝一定階段，表面干燥無無明顯水份的情況下，均勻撒布一層與硬化材料配套的脫模粉。
7．用模具壓制圖案：用所選擇的圖案模板進行表
Make stable a quality carborundum wearable Floor is a party or even every B customers sought, but prone to all kinds of sorts of quality problems after carborundum wearable Floor construction is completed, here we are with Emery wear Ping often cracking phenomenon analysis, cracking occurs after carborundum wearable Floor molding mainly in the following aspects:
1, the received light is not in place, compactness is not good;
2, grasp the initial setting of concrete, not to mention the pulp when watering;
3, you must use the curing agent (liquid barrel do 500 square feet, the summer harvest is completed after three hours of light available for conservation, mop winter curing agent can still be used after freezing.);
4, concrete (water-cement ratio) label is not enough;
5, concrete solidification time is too long;
6, the number or amount of material colorful art Floor hardening agent is an even available including special mineral aggregate, inorganic pigments and additives, high strength wear-resistant flooring materials, the advantage of easy construction, a shape, using a long period , construction of fast, easy to repair, even coloring, not fade and so on. At the same time solve the ordinary color Road Floor integrity is poor, rugged, easy to loose, short life cycle and other shortcomings. The hardener material with color embossed Floor wearable, non-slip, antifreeze, can not afford to dust, easy to clean, high-density, high strength, impact resistance, elegant colors and pattern of three-dimensional level, and can be chosen at random match. Is currently the plaza, parking, streets, parks trail, living area, ideal for senior municipal roads using floor, to replace the color Road Floor ideal alternative. Art embossed floor
Colorful art Floor construction program:
First, grassroots concrete construction requirements: basic level concrete strength C25, its water-cement ratio as low as possible
Second, the construction process:
1. Check the concrete base layer quality: full compliance with the technical requirements of the situation to start construction.
2. Concrete surface roughed: On new poured concrete surface plus C25 Cement 1cm thickness.
3. Select Mold: according to the requirements of customers choose the color patterns mold materials.
4. Spreading hardening material: two-thirds of a predetermined amount of hardener evenly spreading the concrete surface at the initial setting stage, generally at a dose of 4 kg / m2. After the hardener water wetting leveling iron by hand pressure light, and other flooring and then pour a certain stage, and then a second one-third of the material spreader leveling calendering operations.
5. Leveling received light: Check the polished surface quality, check for cracks, bubbles, slag, color all degrees, light concrete leveling jobs based on income, finishing operations were intertwined.
6. Stripping powder dispenser: hardening material at a certain stage of the condensate, dry and free of surface moisture conditions no obvious evenly spreading a layer of hardened material supporting the mold powder.
7. Mold pressing pattern: a table with the selected design template
資訊來源：<聯系電話:400-0709-910>
|
您當前的位置: 首頁 > 行業資訊
